FOREHAND ARMS COMPANY SERIAL NUMBERS SERIAL NUMBERS
FOREHAND ARMS COMPANY SERIAL NUMBERS SERIAL NUMBER

Game 265: july 26, 2019the initials game. Shortages were common until Ordnance arranged for additional barrel manufacturers.Дuring the first half of production the barrels were often mounted on a receiver within 1-2 months of when the barrel was made. The ebb and flow of mass production created parts surpluses and shortages for all the prime contractors, barrels included. Four of the prime contractors did not have the ability to manufacture barrels. If inventory ran out it could shut down production. Given the high volume of production, receivers were generally assembled as part of a carbine within a few months after the receiver was serial numbered.Д«arrels were a critical component in the production lines.

FOREHAND ARMS COMPANY SERIAL NUMBERS SERIAL NUMBER

No documentation from Ordnance, or any of the prime contractors, has been found that indicates the date and serial number of carbines as they were assembled or when they passed final inspection. If a receiver was scrapped and not used, its serial number may or may not have been reused.

Inland receivers initially rejected because of an off spec deep hole drilled for the recoil spring and guide, later recovered and altered to use a detachable main spring housing). As solutions to old problems were learned, some of the same receivers were brought back online and completed (i.e. Serial numbered receivers that failed to pass inspection were set aside as rejects if the defect(s) could not be brought up to minimum standards. Carbine Models M1 or M1A1, and some of the M2's, were made well after the receiver was completed as all of these models used the same receiver. The decision for which receivers would be used for the U.S. The serial number was placed on the carbine receiver during the manufacturing process of the receiver, not when the carbine was finally assembled.

FOREHAND ARMS COMPANY SERIAL NUMBERS SERIAL NUMBERS

One manufacturer separated out smaller blocks of serial numbers for use by subcontractors who would use these serial numbers concurrent to receivers being made by the prime contractor and/or other subcontractors assigned lower or higher serial number blocks. Some manufacturers used more than one block in the same time frame.ДЄ few of the manufacturers used subcontractors to manufacture their receivers. Some of these blocks were split up and used before or after other blocks. There was no requirement as to using the serial numbers in order.ДЄ few manufacturers used some serial number blocks out of order. Contracts had a completion date but there was no requirement for completing one contract before starting another. Think of each serial number block as a separate contract. Serial number blocks were assigned by the Ordnance Department on an as needed basis, generally in response to the awarding of a contract to a given manufacturer. This is not an accurate means of estimating the date the carbine was finally assembled or when it passed its final inspection. Some people estimate a carbine's date of manufacture by adding the quantities manufactured month to month to the assigned serial number blocks. Understanding Serial Numbers - Understanding Dates of ManufactureДating a carbine by its serial number alone is difficult and not always accurate given the circumstances inherent with manufacturing and the logistics situation during the time the carbines were manufactured. Inland Mfg - Engineering & Presentation Gifts I was just curious if we have anyone on here that is expert in Iver Johnson shotgun history.

The one quirk I find interesting is that this gun has a serial number and all major parts of it are serial numbered ( stock, forend wood and metal, butt plate and the barrel). Whats offered here may change slightly as more information becomes available. Collecting and analyzing the serial numbers and their markings. Reconstruction of the dates of manufacture has been based on the history of the company, markings on the receivers, the firearms serial number and the AFMER reports. This revolver originated as a means to use excess leftover parts from the Safety Automatic Revolver, Second Model (Black Powder) when the Safety Automatic Revolver, Third Model (smokeless) was introduced in 1909. Revolver Company revolver was made by Iver Johnson Arms and Cycle Works in the period 1910-1935. SERIAL NUMBERS AND DATES OF MANUFACTURE FOR IVER JOHNSON. In 1915 they were incorporated as Iver Johnson's Arms and Cycle Works Inc. Then in 1902 they bought part of the Forehand Arms Co. And operated as Iver Johnson Sporting Goods.

Forehand arms company serial numbers